Assessing the sustainability of a manufacturing process using life cycle assessment technique—a case of an Indian pharmaceutical company

Clean Technologies and Environmental Policy - Manufacturing organizations are under continuous pressure to implement sustainability in their activities. There is a need to identify the...     

A birth-process approach to Moranda's geometric software-reliability model

To alleviate some of the objections to the basic Jelinski Moranda (JM) model for software failures, Moranda proposed a geometric de-eutrophication model. This model assumes that the times between failures are statistically-independent exponential random variables with given failure rates. In this model the failure rates decrease geometrically with the detection of a fault. Using an intuitive approach, Musa, Iannino, Okumoto , see also Farr , derived expressions for the mean and the intensity functions of the process N (t) which counts the number of faults detected in the time interval [O, t] for the Moranda geometric de-eutrophication model. N (t) is studied as a pure birth stochastic process; its probability generating function is derived, as well as its mean, intensity and reliability functions. The expressions for the mean and intensity functions derived by MIO are only approximations and can be quite different from the true functions for certain choices of the failure rates. The exact expressions for the mean function and the intensity function of N (t) are used to find the optimum release time of software based on a cost structure for Moranda's geometric de-eutrophication model.     

Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

Defocusing image to pattern contact holes using attenuated phase shift masks

The patterning of contact holes by selecting out-of-focus image plane (defocus) using attenuated phase shift masks (APSM) has been studied. Defocus is found to enhance the image modulation at low partial coherence for contact holes with negative local average of mask function. Semi-dense holes up to 130 nm in 8% APSM have been printed by 0.5 μm defocus at a partial coherence of 0.31 using KrF scanner with highest numerical aperture of 0.68. However, these holes were closed with in-focus imaging. Defocus is also found to be beneficial for patterning the pitches that have extensive side lobes with in-focus imaging.     

Formation of a geometric pattern with a mobile wireless sensor network

Mobile wireless sensor networks (MWSNs) will enable information systems to gather detailed information about the environment on an unprecedented scale. These self‐organizing, distributed networks of sensors, processors, and actuators that are capable of movement have a broad range of potential applications, including military reconnaissance, surveillance, planetary exploration, and geophysical mapping. In many of the foreseen applications, the MWSN will need to form a geometric pattern without assistance from the user. In military reconnaissance, for example, the nodes will be dropped onto the battlefield from a plane and land at random positions. The nodes will be expected to arrange themselves into a predetermined formation in order to perform a specific task. Thus, we present algorithms for forming a line, circle, and regular polygon from a given set of random positions. The algorithms are distributed and use no communication between the nodes to minimize energy consumption. Unlike past studies of geometric problems where algorithms are either tested in simulations where each node has global knowledge of all the other nodes or implemented on a small number of robots, the robustness of our algorithms has been studied with simulations that model the sensor system in detail. The simulations demonstrate that the algorithms are robust against random errors in the sensors and actuators. © 2004 Wiley Periodicals, Inc.     

Reversed Temperature-Dependent Propagation Delay Characteristics in Nanometer CMOS Circuits

The supply voltage to threshold voltage ratio is reduced with each new technology generation. The gate overdrive variation with temperature plays an increasingly important role in determining the speed characteristics of CMOS integrated circuits. The temperature-dependent propagation delay characteristics, as shown in this brief, will experience a complete reversal in the near future. Contrary to the older technology generations, the speed of circuits in a 45-nm CMOS technology is enhanced when the temperature is increased at the nominal supply voltage. Operating an integrated circuit at the prescribed nominal supply voltage is not preferable for reliable operation under temperature fluctuations. A design methodology based on optimizing the supply voltage for temperature-variation-insensitive circuit performance is proposed in this brief. The optimum supply voltage is 45% to 53% lower than the nominal supply voltage in a 180-nm CMOS technology. Alternatively, the optimum supply voltage is 15% to 35% higher than the nominal supply voltage in a 45-nm CMOS technology. The speed and energy tradeoffs in the supply voltage optimization technique are also presented     

Mixed oxide supported hydrodesulfurization catalysts—a review

Support effects form important aspect of hydrodesulfurization (HDS) studies and mixed oxide supports received maximum attention in the last two decades. This review will focus attention on studies on mixed oxide supported Mo and W catalysts. For convenience of discussion, these are divided into Al₂O₃ containing mixed oxide supports, TiO₂ containing mixed oxide supports, ZrO₂ containing mixed oxide supports and other mixed oxide supports containing all the rest. TiO₂ containing mixed oxides received maximum attention, especially TiO₂–Al₂O₃ supported catalysts. A brief discussion about their prospects for application to ultradeep desulfurization is also included. An overview of the available literature with emphasis on research carried out in our laboratory form the contents of this publication.     

Effect of oxygen deficiency (δ) on transition temperature of yttrium cuprate superconductors

The nature of pairing mechanism as well as transition temperature of yttrium cuprates is discussed using the strong coupling theory. An interaction potential has been developed for the layered structure with two conducting CuO₂(a–b) layers in a unit cell. The interaction potential properly takes care of electron-electron, electron-phonon and electron-plasmon interactions. Furthermore, the electron-phonon coupling parameter (λ), the modified Coulomb repulsive parameter (μ*) and the 2D acoustic phonon (plasmon) energy as a function of oxygen deficiency is worked out. Finally, the superconducting transition temperature (T _c) is then evaluated by using these coupling parameters and obtainedT _c = 95(92)K for Y(Yb)Ba₂Cu₃O_7−δ superconductors withδ = 0·0. The model parameters estimated from the layered structure approach are consistent with the strong coupling theory. The result deduced on the variation ofT _c withδ are in fair agreement with the earlier reported data on yttrium cuprates. The analysis of the above results are discussed.